Browse all practice questions for the Type II EPA 608 Certification Practice Exam. Search by topic, open any question and review its full explanation, then test yourself in the practice quiz.

Type II EPA 608 Certification Practice Exam course image
More practice questions

These questions are part of the practice quiz. Start practicing

  • What occurs to a refrigerant when it is above the saturation temperature?
  • Which refrigerant is primarily used in commercial refrigeration applications?
  • Which type classification do CFC R-12, HCFC R-22, and HFC 134a share?
  • What is the EPA's definition of the leak repair category for air-conditioning appliances used in occupied facilities?
  • What leak rate triggers the EPA requirement for repairing commercial refrigeration systems containing 50 pounds or more of R-22?
  • What could indicate a refrigerant leak during system inspection?
  • Under what condition should a recovery cylinder be used?
  • What is the result of a malfunctioning pressure relief valve?
  • When is it prohibited to use system-dependent recovery equipment?
  • Which of the following statements about recovering and recycling equipment is false?
  • When is it against EPA regulations to use system-dependent recovery equipment?
  • What is the primary purpose of leak detection tests in refrigeration systems?
  • What should be done with the refrigerant trace gas and nitrogen after a leak is detected?
  • Which of the following statements about recycling and recovery equipment is FALSE?
  • What is required for recycling and recovery equipment to comply with EPA regulations?
  • What is the best use for testing with soap bubbles?
  • What annual leak rate triggers the need for repair in a low pressure chiller used for comfort cooling?
  • What is the primary water source for a water-cooled recovery unit's condensing coil?
  • What should be checked to ensure a pressure relief valve is functioning correctly?
  • What is the proper action if you encounter a compressor that has overheated?
  • Which action is performed after initial liquid removal during refrigerant recovery?
  • What is one of the key reasons for performing a vacuum before charging a system?
  • After leaving the purge unit of a low-pressure centrifugal system, where does the refrigerant go?
  • What is a key indicator of a system leak during testing?
  • According to ASRAE Standard 15-2013, room sensors and alarms are required to detect:
  • What is the purpose of evacuating a refrigeration system?
  • What should technicians do if they find that a system has lost refrigerant?
  • What is the leak rate threshold for industrial process refrigeration according to EPA regulations?
  • Which refrigerant does not require a room detector under ASHRAE Standard 15 if the ventilation system runs continuously?
  • What is the primary function of a pressure relief device in a refrigerating system?
  • Which refrigerant is commonly phased out due to environmental regulations?
  • What is a potential consequence of not using a filter drier in a refrigeration system?
  • What should be done if there is a system with an unknown refrigerant?
  • What essential protection do all refrigeration and HVAC systems feature?
  • What should be done after reaching the required recovery vacuum on an appliance?
  • Recovering refrigerant from a system in the vapor phase primarily minimizes the loss of which component?
  • What government entity outlines leak repair regulations for commercial refrigeration systems?
  • What is a common symptom indicating a potential issue during the refrigerant recovery process?
  • To prevent freezing the water in a water-cooled heat exchanger of an R-134a system during charging, what initial vapor pressure should be used?
  • If a chiller containing 150 pounds of HCFC refrigerant is leaking above the threshold, what must be done within 30 days?
  • Which statement is FALSE regarding recycling and recovery equipment?
  • What is the first step required before recovering refrigerant from an R-410A unit using a recovery machine with R-22 refrigerant?
  • What is the most common leakage point in a belt-driven non-hermetic compressor that has been unused for some time?
  • You are changing out a compressor in a system with 40 pounds of R-404A. After isolating the compressor, what should you do?
  • What type of recovery equipment is generally prohibited for use when the appliance contains significant amounts of refrigerant?
  • In the context of refrigerants, what does "R" stand for?
  • Which type of equipment can be serviced with a Type III certification?
  • A comfort-cooling appliance containing 50 pounds or more of R-22 is found to be leaking beyond the applicable leak rate threshold. How many days do you have to repair the leak and conduct the initial leak verification?
  • What action is appropriate if a system's pressure fails to rise after evacuation?
  • What should be checked before using a recovery unit to remove a charge from a system?
  • To what vacuum level must an appliance or component with over 200 pounds of R410A be evacuated before a major repair?
  • What is the primary function of a pressure relief valve in a refrigeration system?
  • After reaching the required recovery vacuum on an appliance, what should technicians do next?
  • Which component is essential for the safety of a refrigerating system?
  • What method can be used to hasten the removal of refrigerant from a system?
  • What is the evaporation temperature of R-134a at 0 psig?
  • What could be a consequence of leak testing a low-pressure refrigeration system with nitrogen in excess of 10 psig?
  • What usually indicates a compressor burn-out when servicing a refrigeration unit?
  • When could a reciprocating compressor be damaged if energized?
  • Under what condition can refrigerants in appliances be recovered to atmospheric pressure?
  • What is the effect of pressurizing a system without following proper procedures?
  • What is the main purpose of a pressure relief valve in refrigeration systems?
  • In a refrigeration system, what does dry nitrogen break during the dehydration process?
  • Which refrigerant does not require a refrigerant detector in the equipment room if mechanical ventilation is running continuously?
  • Why is it important to install pressure relief valves correctly?
  • What is the consequence of not adhering to EPA regulations regarding refrigerant leaks?
  • Which of the following is a critical factor in handling refrigerants according to EPA standards?
  • What must a refrigerating system have to ensure safety under high pressure conditions?
  • What happens if refrigerant is left in a system without proper maintenance?
  • Which part of a cooling system is most likely to have issues after prolonged inactivity?
  • Before recovering refrigerant from an R410A unit using a recovery unit that previously contained R-22, what must be done?
  • Which of the following actions should be avoided when working with recovery and recycling equipment?
  • Why is it necessary to change the filter in a recovery unit when switching refrigerants?
  • At what pressure will a rupture disk for a low-pressure chiller rupture?
  • Recovering refrigerant from a system in the vapor phase will minimize the loss of which substance?
  • Which of the following is a critical factor in selecting a pressure relief valve for a refrigerant application?
  • What is the appropriate response if an appliance is leaking refrigerant?
  • What might be necessary during evacuation if there is a large amount of moisture in the system?
  • What is the main purpose of recovering refrigerant from an air-conditioning system?
  • What steps should be taken before using a recovery unit to remove a charge?
  • What does a crankcase heater primarily prevent during low ambient temperatures?
  • What is the primary use of compressor heaters in refrigeration and air-conditioning systems?
  • What is the leak rate threshold starting in 2019 for R-22 that requires repair by the EPA?
  • Which gas is typically used for pressure testing in refrigeration systems?
  • What safety consideration is necessary when working with recovery equipment?
  • What is a key consideration when sizing pressure relief devices?
  • At which phase is refrigerant initially removed during the recovery process to optimize time?
  • When is it against EPA regulations to use system-dependent recovery equipment?
  • Why is it important to use a pressure regulator when using dry nitrogen during the vacuum process?
  • What method can be used to pressurize an R-1233ZD system for non-major repairs?
  • During what condition should the chiller be leak tested to ensure safety?
  • Which of the following refrigerants is classified as an HFO?
  • Which situation could potentially result in damage to a reciprocating compressor?
  • When performing recovery operations, what is the first step technicians should take?
  • A refrigerant sensor with alarms and automatic ventilation activation in occupied rooms adheres to which standard?
  • What describes a compressor's role in a refrigeration system?
  • What should be done after reaching the required recovery vacuum on an appliance?
  • Which of the following maintenance actions is important for hermetic compressors during refrigeration cycles?
  • Which symptom indicates a leak in a high pressure system that utilizes a capillary tube?
  • Where in a refrigeration system does oil foaming usually occur?
  • What can the improper installation of a pressure relief valve lead to?
  • In a chiller, where do air and other noncondensables collect?
  • Who is responsible for ensuring compliance with EPA regulations during refrigerant recovery?
  • What is the best practice for handling refrigerants?
  • After a leak repair of a supermarket rack using R-22, when must a follow-up leak verification test be conducted?
  • Which method is NOT typically used for pressurizing refrigeration systems?
  • Which of the following statements about recycling and recovery equipment is FALSE?
  • After servicing a refrigerant leak, what must be verified before reconnecting the system?
  • When first inspecting a hermetic system known to be leaking, what should you look for?
  • What should a technician do after reaching the required recovery vacuum on an appliance?
  • What can be used to pressurize a chiller system before opening it for a non-major repair?
  • Recovered refrigerant may contain which of the following impurities?
  • What must be checked to ensure safe operation of recovery equipment?
  • Why do gauge set hoses used for field service work have self-sealing connectors or hand valves?
  • At what refrigerant charge should a system be serviced if it has been found leaking?
  • Under what circumstance can refrigerant in an appliance be recovered to atmospheric pressure?
  • What is the best method to charge a system that has both an air-cooled condenser and evaporator with a nameplate charge of 80 pounds?
  • Every refrigerating system must be protected by which of the following?
  • How long must an HVAC service company keep records of each disposed appliance with a charge of 5 to 50 pounds?
  • When should refrigerant be removed from the condenser outlet?
  • What is the most efficient method of leak checking a charged low-pressure refrigeration unit?
  • Why might an oil sample need to be taken from a refrigeration unit?
  • In terms of HVAC systems, what does the acronym ‘EPA’ stand for?
  • What could happen if the discharge service valve is closed while the compressor is running?
  • To what aspect of refrigerating systems do pressure relief devices primarily contribute?
  • How long must records be kept when evacuating refrigerant from appliances with a full charge between 5 and 50 pounds?
  • What timeframe is established for repairs if a system exceeds the maximum leak limit?
  • After recovering refrigerant from an air-conditioning system, how can the refrigerant be reused?
  • Why could a recycling or recovery machine with a hermetic compressor overheat when drawing deep vacuums?
  • When first inspecting a hermetic system known to be leaking, what should you look for?
  • What action must be taken if a supermarket system with R-22 leaks more than 125% of its full charge in one year?
  • Before making a major repair on an appliance with over 200 pounds of R-410A, to what level must it be evacuated?
  • After all the liquid has been removed from an average 350-ton system, approximately how much vapor refrigerant remains?
  • Which gas should be used to help locate a leak when a trace gas becomes absolutely necessary?
  • To what micron level should a system be evacuated during dehydration?
  • Which repair is always classified as "major" according to EPA regulations?
  • How would you remove moisture from refrigerant in a system?
  • What can cause a recycling or recovery machine with a hermetic compressor to overheat when drawing deep vacuums?
  • In what scenario can multiple pressure relief valves be beneficial?
  • When should refrigerant be removed from the condenser unit?
  • Under what circumstances may appliances containing refrigerants be recovered to atmospheric pressure?
  • After refrigerant liquid has been recovered from the appliance, what should be done with any remaining vapor?
  • What action should be taken to minimize refrigerant loss from the purge unit on an R-123 chiller?
  • For what refrigerant is an equipment room refrigerant detector not required under ASHRAE Standard 15 provided the mechanical ventilation system in the machinery is run continuously?
  • What must be included on leak inspection records submitted to the EPA for an appliance leaking 125% or more of 50 pounds or more of a regulated refrigerant?
  • Under what circumstances can refrigerants in appliances be recovered to atmospheric pressure?
  • What is the first step to take when a newly assembled system is ready for testing?
  • When recovery first starts, which phase is the refrigerant removed to save recovery time?
  • Which statement about recycling and recovery equipment for stationary refrigeration is FALSE?
  • What is a potential issue with a recycling or recovery machine using a hermetic compressor?
  • Which refrigerant would typically be used in a low-pressure appliance?
  • What is the next step after achieving the required recovery vacuum on an appliance?
  • After refrigerant liquid has been recovered from the appliance, how is any remaining vapor handled?
  • Where is the rupture disk typically located on a centrifugal chiller?
  • For industrial process refrigeration units, what annualized leak rate must be met for repairs?
  • Why is refrigerant vapor re-introduced to the chiller before refrigerant liquid after servicing?
  • Where can pressure relief valves be installed?
  • What effect do non-condensables have in a refrigeration system?
  • What is a moisture indicating sight glass used for?
  • What should be done before transferring refrigerant to an empty cylinder?
  • What should you do after isolating the compressor in a system containing R-404A?
  • How does a chiller that allocates 55% of its capacity for manufacturing and 45% for air conditioning classify in terms of leak rate?
  • What can be done with refrigerant recovered from an air-conditioning system that is held in a refillable cylinder for coil replacement?
  • In operating one’s refrigerating system, what regular checks are necessary for pressure relief valves?
  • What issue can non-condensables cause in a refrigeration system?
  • What is a crucial step immediately after recovering refrigerant?
  • For a chiller containing 50 pounds or more of R-123 that is leaking, what is the EPA-required leak rate for repair starting in 2019?
  • When recovery of refrigerant first starts, in which phase is the refrigerant removed to save recovery time?
  • Which type of repair is classified as "major" under EPA's regulations?
  • Where is the purge unit located in a low-pressure system?
  • What is the primary goal of leak checks in refrigeration systems?
  • If a strong odor is detected during the recovery process, what may have occurred?
  • Which safety device prevents excessive pressure buildup in a refrigerating system?
  • What should be done if leaking industrial process refrigeration exceeds the threshold leak rate?
  • When changing out the compressor of a system containing 40 pounds of R-404A, what is a crucial procedure?
  • According to EPA regulations, which component's removal is classified as a "major repair"?
  • To what level must an appliance containing more than 200 pounds of R-410A be evacuated before repair?
  • Which precaution should be taken when working with a crankcase heater?
  • Who establishes the refrigerant safety group standard?
  • What must be done before recovering refrigerant from an R-410A unit if your recovery/recycling machine contains R-22 refrigerant?
  • When is it against EPA regulations to use system-dependent recovery equipment?
  • Under what condition is the use of system-dependent recovery equipment against EPA regulations?
  • What should be done before removing a compressor from a system containing R404A?
  • When changing out the compressor of a system with 40 pounds of R-404A, what procedure should be followed after isolating the compressor?
  • What is the purpose of using a pressure relief device in refrigeration systems?
  • What type of maintenance should be performed regularly on a refrigeration system?
  • What is the EPA-required evacuation level for recovery or recycling equipment manufactured or imported on or after November 15, 1993?
  • What is the primary purpose of a recovery system?
  • Which category of leak repair is defined by the EPA for refrigeration appliances in retail food and cold storage?
  • Which action is essential before conducting any maintenance on a refrigerant system?
  • When can refrigerants in appliances be recovered to atmospheric pressure?
  • In the context of recovery systems, what does achieving a deep vacuum enable?
  • What is the maximum pressure that should be used when leak testing a low-pressure chiller?
  • Where must you connect a hose to recover liquid refrigerant?
  • What is one of the main reasons for having a redundant pressure relief system in place?
  • What could cause a recycling or recovery machine with a hermetic compressor to overheat while drawing deep vacuums?
  • What is the reason refrigerant cannot be recovered without isolating a parallel compressor system?
  • What should be done before transferring refrigerant to an empty cylinder?
  • How long must owners and operators of regulated appliances normally containing 50 or more pounds of HCFC refrigerant keep records of leak inspections, initial leak verification, and follow-up verification tests?
  • After installing a field piped split system, which gas is recommended for initial pressurization and leak checking?
  • If the initial leak verification test fails after a repair, what is the next step?
  • What is the primary water source used for a water cooled recovery unit's condensing coil?
  • When recovering refrigerant, what is a critical factor to monitor during the process?
  • What is recommended to break the vacuum when dehydrating by the triple evacuation method?
  • What precaution should be taken before performing maintenance on refrigerant systems?
  • Which repair is always considered "major" under EPA regulations?
  • When refrigerant recovery from a system using R-11 or R-123 begins, what is the first step?
  • What must an owner of a commercial refrigeration appliance charged with 2000 pounds of R-22 do after exceeding a leak rate threshold?
  • Pressure relief valves can be installed in which configuration?
  • When should a recycling machine be serviced according to best practices?
  • What is best practice when dehydrating using the triple evacuation method?
  • Which of the following actions is NOT compliant with EPA regulations for a leaking chiller?
  • What is NOT required to mothball an appliance to extend the leak repair deadline?
  • What is one effective way to speed up the removal of refrigerant charge from a system?
  • What is the state of the refrigerant leaving the receiver in a refrigeration system?
  • What is the best practice when using the triple evacuation method for dehydration?
  • An operating unit that has a receiver/storage tank requires refrigerant system service. What should be done when servicing the unit?
  • Which of the following repairs is always considered "major" under EPA regulations?
Subscribe

Get the latest from Passetra

You can unsubscribe at any time. Read our privacy policy